These Operating Instructions are valid for the 82XX controllers of the E-. 1x. 1x. -V reduced assembly depth (). Type. Design. Manual. S. = Global Drive. Frequency inverters Page 2. This Manual is valid for 82XX controllers as of version: X-. E-. DC Drives Lenze PositionServo User Manual EVFE EVFE EVFE EVFE Variant ”reduced assembly Variant ”reduced assembly.
|Language:||English, Spanish, German|
|Distribution:||Free* [*Registration Required]|
lenze inverter manual EVFE datasheet, cross reference, circuit and application notes in pdf format. Lenze. Lenze Drive Systems GmbH, Postfach 52, D Hameln E- mail: [email protected] · Internet: trovotinuldes.gq . Manual-remote changeover. (PDF) EVFE Datasheet PDF, Lenze Global Drive Frequency inverters cross reference, chip, Semiconductor, circuit, Electric, manual, substitute.
Ward Field bourbonnais remove the playlist. Bourbonnais Travel Guides; remove the playlist. Latest Videos; remove the playlist. Longest Videos; Bourbonnais; Collage.
HPQ Co. E82zbb lenze motec, service Manual Lenze vector, original 88 Lenze Manual has 24 challenging levels and is a frustratingly fun Lenze Manual game, The object is to unscramble the Lenze Manual to form the starting.
Real-time pricing, availability fast worldwide shipping on the Lenze World's leading marketplace. This Manual is valid for 82XX controllers as of version: Change and store parameters with the BB operating module. Instruction manual A: Kabelbinders Lenze evf E freqentieregelaar. Download for free Lenze series pdf Owner manual without registration. Lenze personnel have carefully checked this manual and the equipment it Only when using the operating unit BB. Follow the same procedure for the vector frequency inverter.
If the exhaust air contains pollutants dust, lint, grease, aggressive gases then appropriate counter-measures must be in place e. Ensure there is enough mounting space. Several units can be mounted directly adjacent to one another without clearance.
Ensure that there is free access for cooling air and that the outlet for used air is not blocked.
Ensure clearance of mm above and below. In the event of continuous oscillations or vibrations, check the use of vibration dampers. The frequency inverters can be fitted as follows into a control cabinet: With the fixing rails included in the scope of supply With a DIN rail mounting up to 3.
These can be used to fix the frequency inverter to the back panel of the control cabinet or to the mounting plate. The mounting rail is fixed to the device in a guideway, providing access to fixing clamps from above and below devices are installed with 4 lateral fixing clamps.
A DIN rail assembly is also available for devices and thermal separation is possible on and devices. Alternatively, the controller can be installed using a fixing rail. You will need an assembly frame and a seal. This may be of particular interest if you are using small machine housings.
The additional filter is assembled directly on the inverter. Required Order ref.
Required current number number M10A 6. Device Automatic circuit breakers Rated current Order ref. You should pay particular attention to: - Mounting - Filters - Shielding - Earth connections The required components are listed in the overview table. For wiring see the power supply connecting diagram Installation information If you follow the measures outlined below you can be sure that no EMC problems caused by the drive system will occur whilst the system is in operation.
Mounting Ensure that there is sufficient contact between the drive controller and mains choke and the earthed mounting plate: - Mounting plates with a conductive surface galvanised, cadmium-coated ensure sufficient long-term contact.
If you are using more than one mounting plate: - Ensure generous contact surfaces when connecting the mounting plates e. When routing the cables make sure that the motor cables are located away from the signal and mains cables. Avoid using a shared terminal strip for mains input and motor output. Keep the wiring as close to the reference potential as possible. Free hanging cables act like aerials. Filters Only use the RFI filters and mains chokes assigned to the devices.
If contactors, motor protection switches or terminals are located on the motor cable: - Connect the shields of the cables connected there and ensure sufficient contact with the mounting plate. In the terminal box of the motor, connect the shield with PE: - Metal screw connections for the cables at the motor terminal box ensure sufficient contact between the shield and the housing of the motor.
If the mains cable between the mains filter and the drive controller is longer than mm: - Shield the mains cable. If you are using a brake chopper: - Connect the shield of the brake resistor cable directly with the brake copper and brake resistor and ensure sufficient contact with the mounting plate. Shield the control cables: - Shield both ends of the digital control cables.
The usual way of doing this is to install the devices in standard enclosed metallic and grounded control cabinets or boxes. Ground connections Use appropriate cables from a central grounding point PE rail to ground all components drive controller, mains filter, motor filter.
You must observe the minimum cross sections defined in the safety regulations: - However, in terms of EMC it is not the cable cross section but the cable area and the contact area which are of key importance, i. Function: Less effects on the mains - the wave form of the mains supply is a closer approximation of a sine wave Reduced mains current - reduction of the r. Please note: Only operate , , , and devices with the appropriate mains choke or mains filter.
Technical data Device Mains choke Order ref. Function: Less effects on the mains - the wave form of the mains supply is a closer approximation of a sine wave.
Reduced mains current - reduction of the r. The noise emitted by the connected consumers must not exceed the defined characteristic. In order to meet the requirements of limiting value class A, you must connect an RFI filter before the devices. The filter does not replace the function of the mains choke. In order to reduce the r. Interference suppression to EN Limiting value class B If the drive is not being operated on an industrial network but in a residential area, it may cause interference on other devices such as radio and television receivers.
In this case you must provide a means of radio interference suppression to EN , limiting value class B.
Threshold characteristic B is significantly lower than and includes threshold characteristic A. In order to meet the requirements of limiting value class B, you must connect an RFI filter before the devices.
Mains chokes are also required for XE devices. I r [A] U mains [V] m [kg] Order ref. The footprint RFI filters for frequency inverters can also be used for frequency inverters.
A mains filter is available for and frequency inverters instead of the combination of RFI filter and mains choke see following pages. It reduces electromagnetic interference into the mains and mains currents.